進口Power-Sonic蓄電池PDC-121100 12V107AH

進口Power-Sonic蓄電池PDC-121100 12V107AH

　　Power-Sonic一直是主導力量在電池業務超過46年。由于我們的承諾我們公司蓬勃發展提供高質量的成本有效的電池,支持水平的服務是的。

　　我們驕傲我們的靈活性和能力迅速采取行動為市場帶來新的行業產品。我們很自豪持有ISO 9001認證覆蓋我們的組織的各個方面。

What is sulfation of batteries?

挪動空調或因裝修而要拆空調的用戶，那在拆空調前一定要讓專業維修人員收氟，并一定要把敞開的管道口和閥門口用原來的絲堵螺帽堵好，要不就用多層塑料布包嚴。假如一旦進水或進土，結果是很嚴重的。保溫套破損了也要及時修補，否則空調的能效損失也是很多的。

什么狀況下要對機房精細空調加氟！

1、運用超越5年以上的（任何一臺分體式空調機都會自然走漏氟立昂）；

2、屢次移機的（空調移機排空時會耗費局部氟立昂）；

3、制冷外機銜接點的粗管暴露處（即低壓管）不結露或不涼的；

4、制冷外機風扇排風不熱的；

5、制冷回氣壓力（粗管）低于0.4兆帕的；

6、緊縮機運轉電流小于銘牌標注正常值的；

7、制冷高壓管（細管）結霜的；

8、制冷空調內機結冰或吹霧的（有時分還伴有內機漏水）；

9、制熱手摸外機銅管接口處粗管不燙手的；

10、空調有走漏點的；

11、空調開機后十幾分鐘就停機的（低壓維護或過熱維護）。

空調缺氟后的現象：

1、氣管閥門發干，用手觸摸沒有明顯的涼感。

緣由是制冷劑缺乏招致蒸發器內的沸騰終結點提早，使該閥的制冷劑過度增大，閥門的溫度升高，大于室外空氣的漏點溫度。

2、液管閥門結霜。

緣由是“缺氟”招致液管內壓力降落，沸點降低，使閥門溫度低于冰點。

3、翻開室內機面板，取下過濾網，可發現局部蒸發器結露或結霜。

緣由是由于制冷劑缺乏，僅僅使局部蒸發器發作了沸騰吸熱，使制冷面積相應減少。

4、室外機排風沒有熱感。

緣由是制冷劑缺乏招致冷凝壓力、冷凝溫度都降低，排風溫度也隨之降低。

5、排水軟管排水?dāng)鄶嗬m(xù)續或基本不排水。

緣由是蒸發器制冷面積減少，結出面積也減少，凝結水量降低。

6、室外機氣、液閥門有油污，有油污就有泄露。

緣由是制冷劑與冷凍油有一定的互溶性，氟從漏點逸出后進入大氣中，而油附著在漏點四周。

7、丈量空調器的工作電流小于額定電流。

緣由是制冷劑缺乏而使緊縮機工負荷減少，電流降落。

8、從室外機充氟口丈量的壓力低于0.45Mpa.

緣由是制冷劑缺乏招致了蒸發壓力降落。

空調缺氟的簡易判別辦法

一臺裝置合格不走漏的空調，三五年，七八年都能夠不加氟。反之，三兩天就可能漏光。如何判別空調缺氟呢？

一試——

空調機正常開啟一段時間后吹到身上的風感到很涼，并能很快到達設定溫度，室外機的緊縮機能像電冰箱一樣開一會兒關一會兒，就能夠說是正常。

二測——

用溫度計丈量室內機的進、出口風的溫差，差值在10℃以上，也算正常，溫差越大闡明格力空調的工況越好，好的可達15℃左右。

Sulfation is the formation or deposit of lead sulfate on the surface and in the pores of the active material of the batteries' lead plates. If the sulfation becomes excessive and forms large crystals on the plates, the battery will not operate efficiently and may not work at all. Common causes of battery sulfation are standing a long time in a discharged condition, operating at excessive temperatures, and prolonged under or over charging.

What are some of the major types of lead acid batteries?
Batteries are divided in two ways, by application (what they are used for) and construction (how they are built). The major applications are automotive, marine, and deep-cycle. Deep-cycle includes solar electric (PV), backup power, and RV and boat "house" batteries. The major construction types are flooded (wet), gelled, and AGM (Absorbed Glass Mat). AGM batteries are also sometimes called "starved electrolyte" or "dry", because the fiberglass mat is only 95% saturated with Sulfuric acid and there is no excess liquid. Flooded may be standard, with removable caps, or the so-called "maintenance free" (that means they are designed to die one week after the warranty runs out). All gelled are sealed and a few are "valve regulated", which means that a tiny valve keeps a slight positive pressure. Nearly all AGM batteries are sealed valve regulated (commonly referred to as "VRLA" - Valve Regulated Lead-Acid). Most valve regulated are under some pressure - 1 to 4 psi at sea level.

蓄電池應用領域與分類：
◆　免維護無須補液；　　　　　　　　　　● UPS不間斷電源；
◆　內阻小，大電流放電性能好；　　　　　● 消防備用電源；
◆　適應溫度廣；　　　　　　　　　　　　● 安全防護報警系統；
◆　自放電?。弧　　　　　　　　　　　　　?應急照明系統；
◆　使用壽命長；　　　　　　　　　　　　● 電力，郵電通信系統；
◆　荷電出廠，使用方便；　　　　　　　　● 電子儀器儀表；
◆　安全防爆；　　　　　　　　　　　　　● 電動工具,電動玩具；
◆　*配方，深放電恢復性能好；　　　　● 便攜式電子設備；
◆　無游離電解液，側倒仍能使用；　　　　● 攝影器材；
◆　產品通過CE,ROHS認證,所有電池　　　　● 太陽能、風能發電系統；
符合國家標準?！　　　　　　　　　　　?巡邏自行車、紅綠警示燈等。 

What is the "Memory Effect" that I have heard about?
NiCad batteries, and to a lesser extent NiMH batteries, suffer from what's called the "memory effect". What this means is that if a battery is repeatedly only partially discharged before recharging, the battery "forgets" that it has the capacity to further discharge all the way down. To illustrate: If you, on a regular basis, fully charge your battery and then use only 50% of its capacity before the next recharge, eventually the battery will become unaware of its extra 50% capacity which has remained unused. The battery will remain functional, but only at 50% of its original capacity. The way to avoid the dreaded "memory effect" is to fully cycle (fully charge and then fully discharge) the battery at least once every two to three weeks. Batteries can be discharged by unplugging the device's AC adapter and letting the device run on the battery until it ceases to function. This will insure your battery remains healthy.

Do I need to charge my new Laptop or Notebook battery?
A new battery comes in a discharged condition and must be charged before use (refer to the devices manual for charging instructions). Upon initial use (or after a prolonged storage period) the battery may require three to four charge/discharge cycles before achieving maximum capacity. When charging the battery for the first time the device may indicate that charging is complete after just 10 or 15 minutes. This is a normal phenomenon with rechargeable batteries. Remove the battery from the device, reinsert it and repeat the charging procedure.

Do I have to condition my Laptop or Notebook battery?
Yes, it is very important to condition or fully discharge and then fully charge the battery every two to three weeks. Failure to do so may significantly shorten the battery's life (this does not apply to Li-Ion batteries, which do not require conditioning). To discharge, simply run the device under the battery's power until it shuts down or until you get a low battery warning. Then recharge the battery as instructed in the user's manual.

My new laptop battery is not Charging. What is wrong?
New batteries are shipped in a discharged condition and must be charged before use. We generally recommend an overnight charge (approximay twelve hours). Refer to the user's manual for charging instructions. Rechargeable batteries should be cycled (fully charged and then fully discharged) two to four times initially to allow them to reach their full capacity. (Note: it is normal for a battery to become warm to the touch during charging and discharging).

New laptop batteries are hard for the device to charge; they have never been fully charged and are therefore "unformed". Sometimes the device's charger will stop charging a new battery before it is fully charged. If this happens, remove the battery from the device and then reinsert it. The charge cycle should begin again. This may happen several times during the first battery charge. Don't worry; it's perfectly normal.

Is it Possible to Upgrade the Device's Battery to a Newer Chemistry?
NiCad, NiMH and Li-Ion are all fundamentally different technologies and cannot be substituted for one another unless the device has been pre-configured from the factory to accept more than one type of rechargeable battery. The difference between them stems from the fact that each technology requires a different charging pattern to be properly recharged. Therefore, the portable device's charger must be properly configured to handle a given type of rechargeable battery. Refer to your owners manual to find out which rechargeable battery types the particular device supports or use our QuickFind search engine to find the device in our database. The database will automatically list all of the battery types supported by the machine.

合格的安裝不漏空調，年，七年或八年不能添加氟。另一方面，可能漏光的天。如何確定氟空調缺乏？
試一試
空調開啟一段時間后吹著風在身上感覺很冷，并能迅速達到設定溫度，壓縮機可以打開一個在冰箱，像一個在冰箱，可以說是正常的。
兩測量
用溫度計測量室內機入口和出口的溫度差，差值超過攝氏度，這也算正常，溫差越大，更好的格力空調的工作狀態，好的可以達到度左右攝氏度。
三看十分鐘后在開機
，打開室內機面板，應看到蒸發器（銅鋁板上全熱交換元件）與冷凝水均勻，如露水，正常（空氣濕度大，少）。如果一半沒有，可能是缺乏氟化物。如局部結霜或結冰都不正常。
四摸
如果在手的室外機可觸摸的地方，十分鐘后可以觸摸啟動。該室外機有兩個銅閥，一個與厚銅管，和一個薄銅管。觸摸閥應該有溫差兩個；粗應低于溫度的罰款，感覺相對涼爽的正常（在高溫也應冷凝水）。觸摸室外風扇不熱，如果不熱可能是缺氟。
五觀測
一半以上的用戶，閥門管接頭和室外機可以檢查室內機漏水跡象明顯，滲漏等現象顯然表明機器有泄漏，由于溢油會溶解氟、漏氟，漏氟會泄漏。
除了以上，在選型、安裝、工作環境都是正常的，或之前的工作是正常的，現在不酷，這可能是缺氟。氟缺乏是zui常見的，但不是*的問題。是不是上述情況必須是缺乏氟化物。而氟化物的增加，也會引起室內溫度的下降而不至于只降風，增加壓縮機的負荷，目前的問題如過大。只有專業維修人員通過認真負責的檢測，根據環境溫度，電壓，電流，機器的工作壓力水平和出口溫度、祛病的綜合判斷可以“對癥下藥”。
如果一年空調（或更少的時間）在需要添加氟化物，修復泄漏部位，然后加氟。像自行車”的*個孩子，后”。
移動空調或裝修中拆除空調用戶必須讓專業維修人員收到空調，必須與原塞螺母擋開管嘴和嘴閥門，或用多層塑料布燕。如果水或進入土壤，后果是非常嚴重的。絕緣罩還及時修復受損，否則空調的能源效率也是一個很大的損失。
空調加氟的具體操作方法

網頁資源有限，電源解決方案，UPS電源/蓄電池具體型號報價，技術咨詢
（說出您的負載、預計延遲時間，我們專門的工程師為您配置*的電源解決方案）