詳細介紹
西門子S7-300電源模塊,西門子PS307電源模塊,西門子PS307電源模塊2A,西門子PS307電源模塊5A,西門子PS307電源模塊10A
訂貨號:6ES7307-1BA01-0AA0
SIMATIC S7-300 調節電源 PS307 輸入:AC 120/230 V 輸出:DC 24 V/2 A
訂貨號:6ES7307-1EA01-0AA0
SIMATIC S7-300 穩壓電源 PS307 輸入: 120/230 V AC,輸出: DC 24 V DC/5 A
訂貨號:6ES7307-1KA02-0AA0
SIMATIC S7-300 穩壓電源 PS307 輸入: 120/230 V AC,輸出: DC 24 V DC/10 A
德國* 現貨銷售 質保一年 歡迎詢價
SIEMENS上海翰粵自動化系統有限公司
:: :
上海翰粵公司在經營活動中精益求精,具備如下業務優勢:
SIEMENS 可編程控制器
1、 SIMATIC S7 系列PLC:S7-200、S7-1200、S7-300、S7-400、ET-200
2、 邏輯控制模塊 LOGO!230RC、230RCO、230RCL、24RC、24RCL等
3、 SITOP直流電源 24V DC 1.3A、2.5A、3A、5A、10A、20A、40A可并聯.
4、HMI 觸摸屏TD200 TD400C K-TP OP177 TP177,MP277 MP377,
SIEMENS 交、直流傳動裝置
1、 交流變頻器 MICROMASTER系列:MM420、MM430、MM440、G110、G120.
MIDASTER系列:MDV
2、全數字直流調速裝置 6RA23、6RA24、6RA28、6RA70、6SE70系列
SIEMENS 數控 伺服
SINUMERIK:801、802S 、802D、802D SL、810D、840D、611U、S120
系統及伺報電機,力矩電機,直線電機,伺服驅動等備件銷售。
西門子S7-300電源模塊,西門子PS307電源模塊 技術規格
電源,類型 | 10 A |
---|---|
訂貨號 | 6ES7 307-1KA02-0AA0 |
輸入 | 單相交流電源 |
額定電壓 V額定輸入 | 120/230 V AC |
電壓范圍 | 85 ... 132 V/170 ... 264 V |
過壓強度 | 2.3 x U輸入 額定, 1.3 ms |
電源緩沖,Iout rated 時 | > 20 ms,Uin = 93/187 V 時 |
額定電源頻率,范圍 | 50/60 Hz; 47 - 63 Hz |
額定電流Iin rated | 4.2/1.9 A |
接通電流限制 (+25°C) | < 55 A, < 3 ms |
I 2 t | < 3.3 A2s |
集成輸入熔斷器 | T 6.3 A/250 V(不可觸及) |
在電源電纜中推薦使用小型斷路器 (IEC 898) | 從 10A 起,特性曲線 C |
輸出 | 可控,隔離直流電壓 |
額定電壓 Vout rated | 24 V DC |
總公差 | ±3% |
| 約 0.1% |
| 約 0.5% |
殘余紋波 | < 50 mVpp (典型值15 mVpp) |
尖峰信號(帶寬:20 MHz) | < 150 mVpp (典型值60 mVpp) |
調節范圍 | - |
狀態指示器 | 24 V綠燈亮,正常 |
開關動作 | U out無過沖 (軟起動) |
起動延時 / 電壓上升 | < 2 s/ 典型值10 ms |
額定電流 Iout rated | 10 A |
電流范圍 | |
| 0 ... 10 A |
| - |
動態過電流 | |
| 典型值38 A,80 ms 時 |
| 典型值38 A,80 ms 時 |
并聯增加功率 | √ |
效率 | |
效率,當 Vout rated, Iout rated 時 | 約 90% |
功率損耗,當 Vout rated, Iout rated時 | 約 27 W |
閉環控制 | |
動態線路補償 | 典型值±0.1% U輸出 |
動態負載補充 | 典型值±2% U輸出 |
負載階躍調節時間 | |
| < 0.1 ms |
| < 0.1 ms |
保護和監控 | |
輸出過電壓保護 | 附加控制回路,< 28.8 V 時關斷,自動重新起動 |
電流限值 | 11 ... 12 A |
短路保護 | 電子停機,自動重啟 |
連續短路 RMS 電流 | < 12 A |
過載/短路指示 | - |
安全 | |
主/次隔離 | √,安全特低輸出電壓 Uout,符合 EN 60950-1 和 EN 50178 |
保護類別 | Class I |
漏電電流 | < 3.5 mA(典型值0.6 mA) |
安全性測試 | √ |
CE 標識 | √ |
UL/cUL (CSA) 認證 | cULus-listed (UL 508,CSA C22.2 No. 142),F(xiàn)ile E143289 |
防爆 | ATEX EX II 3G Ex nA II T4; |
FM 認證 | Class I Div. 2, Group A, B, C, D, T4 |
船級社認證 | 在S7-300系統內 |
防護等級 (EN 60529) | IP20 |
EMC | |
輻射干擾 | EN 55022 Class B |
供電諧波限制 | EN 61000-3-2 |
抗擾度 | EN 61000-6-2 |
運行數據 | |
環境溫度范圍 | 0 至 +60℃,自然對流 |
運輸和存儲溫度 | ?40 ... +85°C |
濕度等級 | 氣候等級為 3K3,符合 EN 60721 規范,無冷凝 |
機械機構 | |
連接 | |
| 每個螺釘型端子,用于 0.5 -2.5 mm 2 實心線/ 細絞線 |
| 有4個螺釘型接線端子,適用于 0.5 - 2.5 mm2 |
| 有4個螺釘型接線端子,適用于 0.5 - 2.5 mm2 |
外形尺寸(寬 x 高 x 深),[mm] | 80 x 125 x 120 |
重量,約 | 0.8 kg |
安裝 | 可安裝在 S7 導軌上 |
附件 | 用于標準安裝導軌的安裝適配器 (6EP1 971-1BA00) |
Technical Specifications
Article No. | 6ES7 307-1KA02-0AA0 |
Technical specifications |
|
Product | PS 307 |
Power supply, type | 24 V/10 A |
Input |
|
Input | 1-phase AC |
Supply voltage |
|
| 120 V |
| 230 V |
|
|
| Automatic range selection |
Input voltage |
|
| 85 … 132 V |
| 170 … 264 V |
|
|
Overvoltage resistance | 2.3 × Vin rated, 1.3 ms |
Mains buffering at Iout rated, min. | 20 ms |
Mains buffering | at Vin = 93/187 V |
Rated line frequency |
|
| 50 Hz |
| 60 Hz |
Rated line range | 47 … 63 Hz |
Input current |
|
| 4.2 A |
| 1.9 A |
|
|
|
|
Switch-on current limiting (+25 °C), max. | 55 A |
Duration of current limiting at 25 °C maximum | 3 ms |
I²t, max. | 3.3 A²·s |
Built-in incoming fuse | T 6.3 A/250 V (not accessible) |
Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker: from 10 A characteristic C |
Output |
|
Output | Controlled, isolated DC voltage |
Rated voltage Vout DC | 24 V |
Total tolerance, static ± | 3 % |
Static mains compensation, approx. | 0.1 % |
Static load balancing, approx. | 0.5 % |
Residual ripple peak-peak, max. | 50 mV |
Residual ripple peak-peak, typ. | 15 mV |
Spikes peak-peak, max. (bandwidth: 20 MHz) | 150 mV |
Spikes peak-peak, typ. (bandwidth: 20 MHz) | 60 mV |
Product feature output voltage adjustable | No |
Output voltage setting | - |
Status display | Green LED for 24 V OK |
On/off behavior | No overshoot of Vout (soft start) |
Startup delay, max. | 2 s |
Voltage rise, typ. | 10 ms |
Rated current value Iout rated | 10 A |
Current range | 0 … 10 A |
Note |
|
delivered active power typ. | 240 W |
short-term overload current at short-circuit during run-up typical | 38 A |
Duration of overloading ability for excess current on short-circuiting during the start-up | 80 ms |
short-term overload current at short-circuit during operation typical | 38 A |
Duration of overloading ability for excess current on short-circuiting during the operational phase | 80 ms |
Parallel switching for enhanced performance | Yes |
Numbers of parallel switchable units for enhanced performance |
|
Efficiency |
|
Efficiency at Vout rated, Iout rated, approx. | 90 % |
Power loss at Vout rated, Iout rated, approx. | 27 W |
Closed-loop control |
|
Dynamic mains compensation (Vin rated ±15 %), max. | 0.1 % |
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. | 2 % |
Load step setting time 50 to *, typ. |
|
Load step setting time 100 to 50%, typ. |
|
Setting time maximum | 0.1 ms |
Protection and monitoring |
|
Output overvoltage protection | Additional control loop, shutdown at < 28.8 V, automatic restart |
Current limitation | 11 … 12 A |
Characteristic feature of the output short-circuit protected | Yes |
Short-circuit protection | Electronic shutdown, automatic restart |
Enduring short circuit current Effective level maximum | 12 A |
Overload/short-circuit indicator | - |
Safety |
|
Primary/secondary isolation | Yes |
Potential separation | Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 |
Protection class | Class I |
stray current |
|
| 3.5 mA |
| 0.6 mA |
CE mark | Yes |
UL/CSA approval | Yes |
UL/cUL (CSA) approval | cULus-Listed (UL 508, CSA C22.2 No. 142), File E143289 |
Explosion protection | ATEX (EX) II 3G Ex nA II T4; cULus (ISA 12.12.01, CSA C22.2 No.213) Class I, Div. 2, Group ABCD, T4, File E330455 |
FM approval | Yes |
FM approval | Class I, Div. 2, Group ABCD, T4 |
CB approval | No |
Marine approval | In S7-300 system |
Degree of protection (EN 60529) | IP20 |
EMC |
|
Emitted interference | EN 55022 Class B |
Supply harmonics limitation | EN 61000-3-2 |
Noise immunity | EN 61000-6-2 |
Operating data |
|
Ambient temperature |
|
| 0 … 60 °C |
| with natural convection |
Ambient temperature |
|
| -40 … +85 °C |
Ambient temperature |
|
| -40 … +85 °C |
Humidity class according to EN 60721 | Climate class 3K3, no condensation |
Mechanics |
|
Connection technology | screw-type terminals |
Connections |
|
| L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded |
| L+, M: 4 screw terminals each for 0.5 ... 2.5 mm² |
| - |
Width of the housing | 80 mm |
Height of the housing | 125 mm |
Depth of the housing | 120 mm |
Installation width | 80 mm |
Installation height | 205 mm |
Weight, approx. | 0.8 kg |
Product feature of the housing housing for side-by-side mounting | Yes |
Mounting type wall mounting | No |
Type of mounting standard rail mounting | No |
Mounting type S7-300 rail mounting | Yes |
Installation | Can be mounted onto S7 rail |
Mechanical accessories | Mounting adapter for standard mounting rail (6EP1971-1BA00) |
Dimensional drawings
訂貨號:
6ES7 307-1KA02-0AA0